PREN Explained: How to Compare Pitting Resistance Before You Approve a Grade

PREN Explained: How to Compare Pitting Resistance Before You Approve a Grade Featured Image
  • Walmay Avatar By Walmay
  • 26 Oct, 2026
  • 16 Minutes Read

PREN is a single number calculated from chromium, molybdenum and nitrogen content that ranks how well a stainless grade resists chloride pitting, and it is only meaningful when you calculate it from the heat analysis on the mill certificate rather than from the grade name. Use it to shortlist grades against your actual chloride level and metal temperature, then confirm the choice with the checks PREN cannot see: crevice geometry, welding, surface finish and stress. Everything below turns that into a documentable approval, including the purchase order wording that stops a supplier quietly shipping a different chemistry.

Key takeaways

  • PREN is Cr + 3.3Mo + 16N computed from a heat analysis. A grade name only gives you a chemistry window, so one order of 316L can run from 22.6 to 29.5, a wider spread than the step up to 317L.
  • State the multiplier with the number. Under 16N, typical 904L edges out typical 2205; under 30N, 2205 moves ahead. The ranking flips with no change to the steel.
  • Crevices, chloride SCC, welds and heat tint, sensitization and surface condition fail projects that passed on PREN alone. These need design and procedure, not more molybdenum.
  • Write the UNS number, the standard, the named formula, the PREN floor and a certificate per heat into the purchase order, and reject individual heats rather than averages.
  • Test evidence such as ASTM G48 ferric chloride or critical pitting temperature is worth paying for when the duty sits near the limit or a leak would stop production.

What PREN Measures, and What It Quietly Ignores

Buyers get into trouble in both directions. Imagine a buyer paying a super duplex premium on a job whose real problem is gasket geometry, and another signing off 316L on a duty where a sister vessel has already pitted through the wall. Both mistakes come from treating PREN as a performance guarantee instead of what it actually is: a composition index.

PREN, also written PRE or PREn, is a weighted sum of three elements in weight percent. The common form is Cr + 3.3Mo + 16N. The coefficients are not arbitrary. Molybdenum is roughly three times as effective as chromium at holding the passive film together against chloride breakdown, and nitrogen contributes disproportionately because it buffers the local acidification that develops inside an active pit. Those weightings come from empirical fits to experimental work. They are a convenient ranking device, not a law of thermodynamics, which is precisely why two different multipliers circulate and why the number moves when the formula changes.

What the number is not

PREN is not a corrosion rate and it is not a test result. It will not tell you how much wall thickness a tank will lose in a year, and it does not appear on a mill certificate unless somebody calculates it. Two heats with identical PREN can behave differently in the same vessel, because the index is blind to microstructure, inclusion content, residual stress and the condition of the surface that actually meets the chloride.

The variables it leaves out

List what PREN ignores and you have a fair map of how chloride projects fail: chloride concentration, metal temperature rather than process temperature, pH, dissolved oxygen, flow velocity, crevice geometry, weld condition and heat tint, surface roughness, and thermal history. When stainless steel rusts in water, the cause is almost always one of those variables, not the grade label on the certificate.

A Grade Name Is a Range of Chemistry, Not a PREN

Here is the sentence that should change how you read every datasheet: a grade name defines a chemistry window, not a chemistry. Product specifications set minimums and maximums for chromium and molybdenum, and usually only a maximum for nitrogen. Run the PREN arithmetic at both ends of the 316L window and you get 22.6 at the floor and 29.5 at the ceiling. That is a spread of 6.9 points, while the gap between typical 316L and typical 317L is about 5 points. A single order of 316L can span more pitting resistance than the step to the next grade up.

Chemistry basis, 316L to ASTM A240 Cr % Mo % N % PREN
Specification floor 16.0 2.0 0.00 22.6
Mid-range value, what a datasheet usually quotes 17.0 2.5 0.05 26.1
Specification ceiling 18.0 3.0 0.10 29.5
A heat landing near the floor on both 16.2 2.1 0.03 23.6

That last row is why a datasheet PREN and a certificate PREN disagree. The datasheet reflects typical mid-range chemistry from a mill’s production history. The certificate reflects one heat, and that heat is the metal in your pipe.

Compute per heat, never per order

Pull the chemical analysis block off each EN 10204 3.1 mill test certificate and recompute PREN from the actual Cr, Mo and N figures. Do not average across the order, and do not accept one PREN declaration covering twelve heats. Averages hide the outlier, and the pipe that fails is always from the outlier. Walmay ships to more than 100 countries with an EN 10204 3.1 certificate on every heat, which is the level of granularity this check needs; a certificate per consignment would leave you guessing. Material is produced to ASTM, ASME, EN, DIN and JIS standards, and across 800+ specifications there is plenty of room for a naming slip.

Where substitution gets in

Trade names are the weak point. A commercial designation, or an equivalent grade offered as an alternative, is exactly where composition drifts, because nothing in the name pins the heat to a UNS number and a chemistry range. Two suppliers can both ship 316L and land four PREN points apart with neither one out of specification.

Austenitic stainless steel plate samples with progressively brighter surface finishes
Austenitic stainless steel plate samples with progressively brighter surface finishes

16N or 30N: The Multiplier That Reorders Your Shortlist

Two formulas are in circulation and they do not rank grades the same way. The 16N form, Cr + 3.3Mo + 16N, dominates European and American material literature. The 30N form, Cr + 3.3Mo + 30N, comes from a different body of work and appears in plenty of real tender documents. Both are legitimate. Mixing them in one comparison is not.

The arithmetic explains it. Under 30N, nitrogen counts almost twice as much, so nitrogen-alloyed grades gain heavily while low-nitrogen austenitics barely move. Run commonly published mid-range chemistry through both. Take 904L at 21% Cr, 4.5% Mo and 0.05% N: it scores about 36.7 under 16N and 37.4 under 30N. Take 2205 at 22.5% Cr, 3.25% Mo and 0.17% N: about 36.0 under 16N and 38.3 under 30N. Under 16N the austenitic is ahead. Under 30N the duplex is ahead by close to a point, and not a gram of metal changed.

Put the formula in the header

A table that compares 904L against 2205 without stating the multiplier is not a comparison, it is a screenshot of someone’s spreadsheet. Put the formula in the column header, write the chosen form into the drawing and the purchase order, and require the supplier to declare their computation. If a seller quotes a PREN without showing the formula and the chemistry behind it, treat the number as unverified.

Nitrogen only counts if it is in the steel

Nitrogen-bearing grades depend on the melting route to retain the nitrogen that makes the calculation work. Read the nitrogen figure on the certificate directly rather than assuming it sits at the typical value. A duplex heat that came in at the bottom of the nitrogen range has given back a chunk of the margin you were buying, and on the 30N formula it has given back more.

Reading the Ladder: What Each PREN Band Actually Buys

PREN is a purchase decision, not a score to maximise. Every step up the ladder is paid for in money, fabricability and delivery time, and the useful question is which step your service actually needs. The numbers below are calculated at the specification floor and ceiling using Cr + 3.3Mo + 16N, with nitrogen taken as zero at the floor because most grades set no minimum for it.

Grade PREN floor PREN ceiling Commonly quoted mid-range Where it stops paying
304/304L 18.0 21.6 18 to 20 Any sustained chloride
316/316L 22.6 29.5 24 to 26 Hot chloride, tight crevices
317L 27.9 34.8 29 to 32 SCC-led duty
904L 32.2 41.1 34 to 36 When strength is the real problem
2205 34.1 37.8 34 to 36 Very high chloride at temperature
2507 37.7 47.6 42 to 43 When the shop cannot weld duplex

The 304 to 316L step is the one that matters

Adding molybdenum for a modest premium buys the cheapest meaningful jump in pitting resistance available to a buyer. Most approval questions are settled at that step, not at the top of the ladder. If your chloride and temperature combination sits inside 316L territory, adding alloy above it buys nothing you will notice.

The 904L and 2205 cluster traps buyers

These two score within a point of each other and people keep choosing between them on the number. Stop. 904L is an austenitic: weldable without ferrite balance concerns, tough, formable with familiar procedures, and it carries roughly 220 MPa minimum yield strength to ASTM A240. 2205 brings about 450 MPa minimum and a different set of fabrication rules on heat input and interpass temperature. Choose on the rest of the duty, not on PREN.

2507 earns its price only under real pressure

Super duplex makes sense where the chloride and temperature combination genuinely demands it and the fabricator can meet the welding and ferrite balance requirements. A badly welded 2507 performs below a well-fabricated 2205, and the premium is gone. Walmay’s stocked range runs from 201 through 304, 316L and 317L to 904L super austenitic and 2507 super duplex, so a shortlist can be priced across the whole ladder instead of one rung.

There is no seawater-safe number

Forget the idea of a universal threshold. Seawater performance turns on temperature, flow, crevice geometry, chlorination and whether the surface stays wet or dries between cycles. The floor you should specify comes from the service and the owner’s specification, not from a forum post quoting 40.

Stainless steel coupons arranged as ascending steps to illustrate a pitting resistance grade ladder
Stainless steel coupons arranged as ascending steps to illustrate a pitting resistance grade ladder

Where a High PREN Buys You Nothing: Five Failure Modes It Cannot See

The index ranks one mechanism. These five routinely sink projects that passed on PREN alone.

Crevices

Attack inside a gasket face, a lap joint, a tube-to-tubesheet gap or under a sediment deposit starts at a lower chloride level and a lower temperature than open-surface pitting. A grade chosen to just clear the open-surface duty will fail in the crevice first, and extra molybdenum does not fix bad geometry. Design the gap out, seal it, or accept that the crevice needs far more alloy than the wetted wall does.

Chloride stress corrosion cracking

PREN says nothing about SCC. Austenitic grades crack under the combination of chloride and tensile stress whatever their molybdenum and nitrogen content, and duplex resistance comes from the ferrite-austenite balance and higher strength rather than from the index. A high PREN austenitic is still an austenitic.

Welds and heat-affected zones

Welding destroys the passive film, can segregate molybdenum and chromium, and leaves heat tint that is itself an initiation site. Without proper cleaning and passivation, the certificate PREN describes metal that is no longer in service. For duplex, heat input and interpass temperature decide the ferrite balance, and getting that wrong costs more performance than one grade step buys. Weld failures usually trace back to the procedure, not the chemistry.

Sensitization and thermal history

Chromium carbide precipitation at grain boundaries pulls chromium out of solution locally, so the chromium at the boundary sits below the figure the calculation used. The mechanism and the annealing window are covered in how annealing temperature affects corrosion resistance in 316L. The point for approval work is that a heat can leave the mill at 26 PREN and arrive in service with sensitized boundaries reading materially lower. Where the specification calls for it, Walmay’s heat treatment options include solution anneal and stress relief, plus H900 to H1150 on 630.

Surface condition

Embedded iron from a shared grinding wheel, polishing residue, a coarse ground finish, or unpassivated heat tint all create initiation sites. A 400-grit ground surface and a 2B surface are not the same material once a chloride film sits on them.

What actually measures the outcome

Ferric chloride pitting and crevice testing to ASTM G48, and critical pitting temperature determination. PREN predicts and G48 confirms. Ask for test evidence where the service sits close to the limit or a leak would stop production, and be honest about the cost and lead time it adds.

Pitting corrosion inside a stainless steel flange gasket groove under raking light
Pitting corrosion inside a stainless steel flange gasket groove under raking light

An Approval Sequence You Can Run Before You Sign

Run these five steps in order and the decision documents itself.

  1. Write the service down in numbers before you look at a grade. Chloride concentration, maximum metal temperature rather than process temperature, pH, whether the surface is continuously wet, intermittently wet or splashed, and every crevice in the assembly. Without those, a PREN target is guesswork wearing a hard hat.
  2. Set a PREN floor and record the formula beside it. Floor, multiplier convention, UNS number and the standard, on the same line of the specification. A floor with no stated formula is not a requirement, it is an invitation to argue later.
  3. Pull the certificates and compute heat by heat. Reject the individual heat that falls short instead of averaging across the order. The pipe that leaks comes from one heat.
  4. Walk the fabrication route. Welding procedure, post-weld cleaning and passivation, solution annealing where specified, final surface finish. This step decides whether the approved PREN survives to commissioning, and it is where most of the real risk sits.
  5. Decide the evidence tier in advance. Open surface, low chloride, ambient service needs the certificate calculation and nothing more. A hot chloride duty with a crevice, or a failure that would stop production, justifies a G48 or critical pitting temperature result on a coupon before the order is released.

Do step 1 properly and the grade usually comes down, not up. Most over-specification starts with a grade chosen before the service conditions were written down, and then the calculation gets bent to defend the choice.

How to Write the Requirement So Nobody Substitutes on You

The clause that holds a supplier to your decision has four parts, in plain language: the UNS number, the standard the material must meet, a minimum PREN stated as calculated by the named formula from the heat analysis, and a mill certificate per heat. Remove any one and the requirement is open to interpretation. A PREN floor with no formula invites the 30N reading. A grade name with no UNS number invites a commercial equivalent.

Decide what happens when a heat misses

Three options: reject and re-offer, accept only with a written deviation approved before shipment, or price a documented concession. Choose at the RFQ stage. Deciding on the dock, with plates on the ground and a crew waiting, is how a 23.6 PREN heat gets accepted against a 25 floor.

Ask for the certificate before release

Not bundled with the shipping documents where nobody has time to open it. The chemistry should be in your hands while the material is still at the mill or sitting in the stockist’s rack.

Re-sourcing changes chemistry

Trade measures move buyers between origins fast. On 12 August 2025, South Korea’s Ministry of Economy and Finance announced a preliminary anti-dumping duty of 21.62% on Chinese-origin hot-rolled stainless steel plates, proposed to run for five years, and that duty reshuffles origin choices for anyone buying plate in the region. Treat that figure as what it is, a preliminary determination: the definitive rate, the product scope it finally covers and whether it is still in force when you read this all have to be confirmed against the official Korean notice before a sourcing plan rests on it. Route changes of that kind are exactly where a different chemistry window enters the supply chain. Walmay Group’s Malaysia hub offers stainless sheets to help clients navigate those shifts. Treat a re-sourced heat as a new heat and recompute.

Over-specification is not a safety habit

Adding five PREN points for comfort often pushes the order out of the austenitic range into duplex, which changes welding procedure, machining, forming and delivery. That can cost more in the shop than the material premium costs at the mill. Spend the effort on the crevice and the weld instead.

Before You Approve: The Checklist and Where to Get the Numbers

PREN is a screening tool that removes grades from a list. It never closes the decision on its own, and it is only as good as the chemistry it was calculated from. So the last question before you approve is where that chemistry comes from.

From the heat, not the grade. A datasheet gives you typical composition for the grade; your plates are one specific heat, and typical is not the same thing. Ask for the EN 10204 3.1 mill test certificate with the quotation, read chromium, molybdenum and nitrogen off it, and run your own formula and multiplier across those figures instead of accepting the supplier’s PREN column as given.

If the shortlist landed on the super austenitic end, Walmay maintains dedicated grade hubs for 904L stainless steel and for 310 and 310S stainless steel, with regular inventory behind them and a standard product lead time of two weeks for planning purposes. The wider stocked range covers the grades this comparison runs through, from 201 and 304 up to 904L and 2507, with an EN 10204 3.1 mill test certificate on every heat and a full mill certificate available with the quotation. That puts heat-level chemistry in your hands before the order is placed rather than after the plates land.

If you have a grade proposal and a set of service conditions on the desk, send both through the contact page. The reply should be the certificate and the calculated PREN, not a brochure.

PREN questions buyers still ask

Does 2205 or 904L have the higher PREN?

They sit within about a point of each other, and which ranks higher depends on the formula and the heat. Under Cr + 3.3Mo + 16N at typical chemistry, 904L comes out marginally ahead. Under Cr + 3.3Mo + 30N, the nitrogen in 2205 puts it ahead. Decide between them on strength, weldability, toughness and fabrication rules instead.

Does a high PREN prevent chloride stress corrosion cracking?

No. PREN covers pitting initiation only. Austenitic grades remain susceptible to chloride stress corrosion cracking under tensile stress at temperature whatever their molybdenum and nitrogen content, while duplex grades resist it through their ferrite-austenite structure and higher strength. Specify SCC resistance as a separate requirement and treat a PREN figure as no evidence at all on that failure mode.

Related Articles